Garage Door Torsion Spring SINGLE RW .250 X 1.75" ID x Select Length - USA MADE*
This Listing is for One Single .250 x 1 3/4" (select the length) Right Wound Quality, USA Made*, Oil Tempered and Coated Garage Door Torsion SpringPlease Read The Complete Listing Below For Our Step By Step Instructions on How to Properly Measure Torsion Springs to Ensure the Proper Springs Are Ordered.Includes one Single Right Wound Torsion Spring1 Replacement Center Bushing or Bearing and Option to Buy Winding Rods are Available by Selecting From the Dropdown List.Wire size is .250, Inside Diameter is 1 3/4", length is selected in the drop-down list (Additional Lengths are Available, Message Us for Quote)Springs are Made of Oil Tempered USA Made Spring Steel, and are coated to resist rust, and for longer lifeProperly sized and installed springs are rated minimum 10,000 cyclesThese Springs are manufactured by One of the Largest OEM Spring Suppliers, The Aluminum Winding And Stationary Cones are Included, And Are Pre-Installed. (*Cones are Imported)2 year Limited Warranty Against Premature Breakage **Cycle Rating is dependent on the springs being properly sized for the door and the correct amount of turns put on the springs for the door height. Technical and Installation Support is Available by Phone or Email. How to select the correct spring (Please Read the Below Instructions Entirely Before Placing an Order)First of all it is very important to have the correct spring for your door, if the spring is not matched correctly to the door, it will not work properly and can be dangerous or damage your operator. Make sure that you measure the spring correctly and if you have questions, please message us before ordering.Step 1 is to measure the wire diameter. To do this you will need to measure 10 coils then compare that measurement to the chart below to see the wire size, double check by measuring 20 coils and compare to the 10 coil measurement, if the 2 measurements do not match, try measuring in a different area of the spring and also make sure the spring is not stretched. Do not measure in the ends where the cones are, the cones stretch the ends where they are installed.. 10-Coil Measurement 20-Coil Measurement Wire Sizeincmincm1 3/4"4.503 1/2"8.990.1771 7/8"4.763 3/4"9.530.1871 15/16"4.883 7/8"9.750.1922"5.084"10.160.2002 1/16"5.264 1/8"10.520.2072 3/16"5.554 3/8"11.110.2182 1/4"5.724 1/2"11.450.2252 5/16"5.954 5/8"11.900.234 2 7/16"6.194 7/8"12.380.2432 1/2"6.355"12.700.2502 5/8"6.675 1/4"13.340.2622 3/4"6.935 1/2"13.870.2732 13/16"7.195 5/8"14.380.283 Step 2 is to determine the spring inside diameter, if the spring is broken you can simply use a ruler to measure the inside of the broken end, if the spring is still in one piece you can measure the outside and deduct the wire size X 2. You also may be able to find stampings on the cones which will help determine the ID, ( P200 or P2000 for 2” and P175 for 1 ¾”) The most common sizes in residential springs are 1 3/4" and 2" ( Raynor doors use 2 ¼” ID ) Step 3 is to measure the length of the spring, Measure the spring only, not including the winding and stationary cone. If the spring is broken measure each piece and add the two measurements together to get the total length. If the spring is still in one piece and wound, it will be longer by 2-3” then when it is relaxed.. the proper way to measure is to unwind the spring to measure the correct length, Step 4 is only important if ordering a single spring, determine the wind direction of the spring, ( right hand wind ( RW) or left hand wind (LW). Below is an example of the different spring winds. This is probably the most confusing part of the spring ordering process, as The RW is normally on the Left side and the LW is normally on the Right side. Be sure to check the wind direction and not make assumptions.If you look at the end of the spring and compare to the third picture on the listing you will be able to determine the correct wind direction. We are a Pro Garage Door Installation and repair Company. We carry many repair parts for many different brands of doors. If you are looking for a part and we don’t have it listed, just message us through eBay and we’ll quote a price and set up a listing for you through eBay.CAUTION: Installing or repairing a garage door can be dangerous task. Garage door springs and cables are under extreme tension and require appropriate safety precautions. Working with garage doors and openers could result in personal injury or death. We recommend all installations, repairs, adjustments, and removals on garage doors be made by a qualified garage door technician. Any attempts to install, repair, replace, adjust garage doors or openers are done at your risk. In no event shall M. C. Overhead Door parts division be liable for damages of any kind, personal injury or death. User assumes all responsibility/risk for use of information and products purchased. By purchasing our products you agree to these terms. RETURN POLICY Returns are accepted within 30 days of the date that the item is received.We don't offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased. Buyer is responsible to pay for the return shippingIf an item is listed with 'free shipping', a 20% restocking fee will be deducted from the refund amount. All items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.
Specifications
| Restocking Fee | 20% |
| Return Shipping Will Be Paid By | Buyer |
| All Returns Accepted | Returns Accepted |
| Item Must Be Returned Within | 30 Days |
| Refund Will Be Given As | Money Back |
| Brand | Unbranded |
| Type | Torsion Spring |
| MPN | Does Not Apply |
| Material | Black Coated Steel |
This Listing is for One Single .250 x 1 3/4″ (select the length) Right Wound Quality, USA Made*, Oil Tempered and Coated Garage Door Torsion SpringPlease Read The Complete Listing Below For Our Step By Step Instructions on How to Properly Measure Torsion Springs to Ensure the Proper Springs Are Ordered.Includes one Single Right Wound Torsion Spring1 Replacement Center Bushing or Bearing and Option to Buy Winding Rods are Available by Selecting From the Dropdown List.Wire size is .250, Inside Diameter is 1 3/4″, length is selected in the drop-down list (Additional Lengths are Available, Message Us for Quote)Springs are Made of Oil Tempered USA Made Spring Steel, and are coated to resist rust, and for longer lifeProperly sized and installed springs are rated minimum 10,000 cyclesThese Springs are manufactured by One of the Largest OEM Spring Suppliers, The Aluminum Winding And Stationary Cones are Included, And Are Pre-Installed. (*Cones are Imported)2 year Limited Warranty Against Premature Breakage **Cycle Rating is dependent on the springs being properly sized for the door and the correct amount of turns put on the springs for the door height. Technical and Installation Support is Available by Phone or Email. How to select the correct spring (Please Read the Below Instructions Entirely Before Placing an Order)First of all it is very important to have the correct spring for your door, if the spring is not matched correctly to the door, it will not work properly and can be dangerous or damage your operator. Make sure that you measure the spring correctly and if you have questions, please message us before ordering.Step 1 is to measure the wire diameter. To do this you will need to measure 10 coils then compare that measurement to the chart below to see the wire size, double check by measuring 20 coils and compare to the 10 coil measurement, if the 2 measurements do not match, try measuring in a different area of the spring and also make sure the spring is not stretched. Do not measure in the ends where the cones are, the cones stretch the ends where they are installed.. 10-Coil Measurement 20-Coil Measurement Wire Sizeincmincm1 3/4″4.503 1/2″8.990.1771 7/8″4.763 3/4″9.530.1871 15/16″4.883 7/8″9.750.1922″5.084″10.160.2002 1/16″5.264 1/8″10.520.2072 3/16″5.554 3/8″11.110.2182 1/4″5.724 1/2″11.450.2252 5/16″5.954 5/8″11.900.234 2 7/16″6.194 7/8″12.380.2432 1/2″6.355″12.700.2502 5/8″6.675 1/4″13.340.2622 3/4″6.935 1/2″13.870.2732 13/16″7.195 5/8″14.380.283 Step 2 is to determine the spring inside diameter, if the spring is broken you can simply use a ruler to measure the inside of the broken end, if the spring is still in one piece you can measure the outside and deduct the wire size X 2. You also may be able to find stampings on the cones which will help determine the ID, ( P200 or P2000 for 2” and P175 for 1 ¾”) The most common sizes in residential springs are 1 3/4″ and 2″ ( Raynor doors use 2 ¼” ID ) Step 3 is to measure the length of the spring, Measure the spring only, not including the winding and stationary cone. If the spring is broken measure each piece and add the two measurements together to get the total length. If the spring is still in one piece and wound, it will be longer by 2-3” then when it is relaxed.. the proper way to measure is to unwind the spring to measure the correct length, Step 4 is only important if ordering a single spring, determine the wind direction of the spring, ( right hand wind ( RW) or left hand wind (LW). Below is an example of the different spring winds. This is probably the most confusing part of the spring ordering process, as The RW is normally on the Left side and the LW is normally on the Right side. Be sure to check the wind direction and not make assumptions.If you look at the end of the spring and compare to the third picture on the listing you will be able to determine the correct wind direction. We are a Pro Garage Door Installation and repair Company. We carry many repair parts for many different brands of doors. If you are looking for a part and we don’t have it listed, just message us through eBay and we’ll quote a price and set up a listing for you through eBay.CAUTION: Installing or repairing a garage door can be dangerous task. Garage door springs and cables are under extreme tension and require appropriate safety precautions. Working with garage doors and openers could result in personal injury or death. We recommend all installations, repairs, adjustments, and removals on garage doors be made by a qualified garage door technician. Any attempts to install, repair, replace, adjust garage doors or openers are done at your risk. In no event shall M. C. Overhead Door parts division be liable for damages of any kind, personal injury or death. User assumes all responsibility/risk for use of information and products purchased. By purchasing our products you agree to these terms. RETURN POLICY Returns are accepted within 30 days of the date that the item is received.We don’t offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased. Buyer is responsible to pay for the return shippingIf an item is listed with ‘free shipping’, a 20% restocking fee will be deducted from the refund amount. All items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.
